NuTech Pavecoat Concrete Sealer 20L Matt
Nutech PaveCoat 20L Matte Concrete Sealer – Natural Finish Driveway & Paving Sealer
Nutech PaveCoat 20L Matte is a premium solvent-based acrylic concrete sealer designed to protect and enhance driveways, paving and decorative concrete surfaces. Delivering a natural low-sheen finish, this matte concrete sealer provides long-lasting protection without the high-gloss “wet look”.
The 20 litre size is ideal for larger driveways, extensive paved areas and commercial projects requiring consistent coverage and professional results. If you are searching for a 20L concrete sealer or a matte driveway sealer that performs in Australian conditions, PaveCoat is a proven solution.
Key Features & Benefits
- Natural matte finish – low sheen appearance
- 20L size ideal for larger surface areas
- Premium solvent-based acrylic penetrating sealer
- Suitable for pedestrian and light vehicular traffic
- Excellent UV resistance – non-yellowing formula
- Resistant to oil and grease staining
- Available in clear and 29 standard colours
- Custom colour matching available
Ideal for Large Driveways & Commercial Applications
PaveCoat 20L Matte is suitable for:
- Residential driveways
- Multi-density housing developments
- Car parks
- Shopping centres
- Industrial and commercial concrete floors
- Stamped, stencil and slate impression paving
Coverage & Application
- Size: 20 Litres
- Recommended Coats: 2 coats
- Coverage Rate: 4–6m² per litre per coat
A 20L drum typically covers approximately 80–120m² per coat, depending on surface porosity and texture.
Allow new concrete to cure for a minimum of 7 days before sealing. For same-day sealing applications, refer to PaveCoat Cure & Seal.
Suitable Surfaces
- Concrete driveways and footpaths
- Paving and exposed aggregate
- Stamped and patterned concrete
- Spray paving
- Concrete roof tiles
- Tilt slab construction
- Cement sheeting
- Workshop and factory floors
Provisions
Pre Coated Surfaces: PaveCoat IS NOT suitable to be used as an over coat for standard enamel floor finishes. To determine the suitability of the pre coated surface, refer Nutech Coating Test Kit or contact Nutech Paint.
Anti-Slip properties: Without the addition of an anti-slip additive, PaveCoat may not be suitable for steep, smooth surfaces or areas of high trafficability. The addition of a Nutech AntiSlip Mix In product is recommended which will meet the performance criteria outlined in AS 4586 and AS 4663 Wet P2 or Wet P3 Pendulum rating, depending on the grade and addition level. Refer to the PaveCoat Application Guide for further information.
Note: For steep inclines and gradients greater than 1 in 14, a P5 or R12 rating will be required. Nutech Paint recommends EPiC PolyCryl (Exterior & Interior) OR EPiC Epoxy 500 (Interior only) with the addition of the suitable AntiSlip Cast On products for this application.
Typical Applications
- Domestic & Multi Density Residential
- Car Parks
- Shopping Centres
- Industrial and Commercial uses
Substrate Recommendations
All types of concrete such as driveways, paving, footpaths, concrete roof tiles, pattern paving, stamped and slate impression paving, stencil paving, spray paving, tilt slab construction and cement sheeting
Notes
General:
- Allow a minimum 7 days for new concrete to cure prior to sealing
- For same day sealing, refer PaveCoat Cure & Seal
- Powdery or soft Concrete: DO NOT etch as this may damage the surface
- Old, Heavily Soiled/Stained Surfaces: Pre-treat the surface with Nu-EcoSafe Degreaser
- For anti-slip properties that meet AS4586 & AS4663 - P2 or P3 ratings Nutech Paint recommends AntiSlip Mix In. Ideally suited for wet areas, pools, factory loading docks, access ramps (with less than a 5° incline), stairs, entrance foyers, public pedestrian and vehicle areas.
- For further information regarding anti-slip suitability, mix ratios and standards compliance please refer to the AntiSlip Mix In TDS or PaveCoat Application Guide
Buy Nutech Pavecoat Driveway Sealer matt finish online or visit our shop.
Colour Accuracy Disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.
Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.
What Our Customers Say
See what trade professionals, contractors and customers have to say about their experience with ProTrade Warehouse.