UltraKote SuperClear WB
is a PREMIUM GRADE new generation two part water based acrylic cross-linking emulsion, Formulated to protect and enhance concrete surfaces whilst providing many advantages over conventional polyurethane coatings. This product is an excellent for grind and seal projects.
Product advantages:
• Excellent for Interior and Exterior coating
• Water based, easy to use
• No solvent fumes or flammable hazards
• Low VOC
• Can be sprayed, brushed or applied by roller
• Quick drying
• Non-Blushing
• Fast water resistance – within 2 hours
• Exceptional gloss finish and also available in matt
• Enhances surfaces
• Hard wearing surface resistant to abrasion
• Hot tyre resistant
• Chemical resistant – oils, greases, alkali
• Resists discoloration from dirt and spills
• UV resistant – Non yellowing
• Provides a dust free surface
Areas of use:
- Flake Floors
- Sealing bare concrete (grind and seal projects)
- Protective coating over metallic floors
- Garage floors
- Patios
- Living rooms
- Office and lobby floors
- Shop floors
- Warehouse floors
- Showrooms
UltraKote SuperClear Matt and Gloss
Assure the surface is fully dry and free of dust or any contamination, caution on new concrete, best to allow 28 days curing prior to sealing.
• Mixing Ratio is 4 Part A to 1 Part B
• Drill mix for 3 minutes to ensure thoroughly mixed | allow standing for 15min to allow aeration to dissipate
• Recommended with 8 -10mm nap roller
• Two coats are recommended for optimum effect.
• Application must not be too thick as excessive build-up may cause the coating to appear milky and thin coats will show roller marks
• Allow 24-48 hours to cure.
• Do not apply when the temperature of concrete is below 10oC.
• Do not apply if rain is imminent.
• Pedestrian traffic is allowed after 24 hours.
• Allow up to 7 days before vehicular traffic access (Dependent on temperature and airflow).
• Clean up equipment with water immediately after use.
Recommended Preparation Method
Preparation is the key to achieving a long-lasting floor-coating system
Diamond grinding is recommended method of preparing new & old substrates prior to applying Ultrakote SuperClear WB.
The purpose behind concrete grinding is to remove the existing coating and other types of contamination completely to achieve a clean surface as well as remove any sealer or curing agent and open concrete pores allowing 1st coat of UltraKote SuperClear WB to penetrate deep into the surface and seal the floor.
Recommended diamond tooling grits to prepare the floor prior to applying Ultrakote High Solids Epoxy are
-
120 - 150 Grit diamond tooling as the final stage of grinding to remove any scratches from the floor
-
PCD plugs to remove flaking paint and then use grinding shoes to smooth out the floor before applying the coating.
Pack Size: 5 Litre Kit (4 Litres Part A + 1 Litre Part B)
Recommended Application Method: Use the UniPro Microfiber Roller
Coverage Guide
For areas up to 20 square meters:
- Apply 1 to 3 litres for the first coat
- Apply 1 to 2 litres for the second coat
- Use 2 generous coats in total
- Number of kits required: 1
For areas 20 to 50 square meters:
- Apply 3 to 5 litres for the first coat
- Apply 3 to 5 litres for the second coat
- Use 2 generous coats in total
- Number of kits required: 2
Notes: This guide is approximate; actual consumption depends on application method, style, and surface porosity. Important: UltraKote SuperClear should NOT be applied using a squeegee.
Colour Accuracy Disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.
Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.
