Nutech PaveCoat Concrete Sealer
PaveCoat is a superior-quality, solvent-based acrylic penetrating sealer that has earned the distinction of being Australia’s leading concrete sealer. Designed for diverse functional, decorative, and protective concrete applications, PaveCoat provides exceptional sealing, colouring, and safeguarding of concrete surfaces, rendering them long-lasting and economical. Its high-performance formula offers robustness to withstand pedestrian and light vehicular traffic. At the same time, its aesthetic appeal makes it an ideal choice for enhancing the appearance of new and old concrete. PaveCoat is available in standard gloss and matte finishes to meet its customers’ unique requirements.
PaveCoat Concrete Sealer is manufactured from acrylic polymer resin and is stabilised for all types of concrete, including:
- Paving
- Driveways
- Factories
- Workshop floors
- Service Stations
- Tilt slab construction
- Asbestos and cement sheeting
- Slate flooring
- Concrete roof tiles
Benefits
- Available in clear and 29 standard colours
- Can be custom colour-matched upon request
- Excellent UV light resistance
- Resistant to fading
- Non-yellowing
- Resistant to oil and grease
Appearance
Clear colourless or coloured viscous liquid
Coats Required
2 Coats
Coverage Rate
4 – 6 m²/L
Provisions
Pre Coated Surfaces: PaveCoat IS NOT suitable to be used as an over coat for standard enamel floor finishes. To determine the suitability of the pre coated surface, refer Nutech Coating Test Kit or contact Nutech Paint.
Anti-Slip properties: Without the addition of an anti-slip additive, PaveCoat may not be suitable for steep, smooth surfaces or areas of high trafficability. The addition of a Nutech AntiSlip Mix In product is recommended which will meet the performance criteria outlined in AS 4586 and AS 4663 Wet P2 or Wet P3 Pendulum rating, depending on the grade and addition level. Refer to the PaveCoat Application Guide for further information.
Note: For steep inclines and gradients greater than 1 in 14, a P5 or R12 rating will be required. Nutech Paint recommends EPiC PolyCryl (Exterior & Interior) OR EPiC Epoxy 500 (Interior only) with the addition of the suitable AntiSlip Cast On products for this application.
Typical Applications
- Domestic & Multi Density Residential
- Car Parks
- Shopping Centres
- Industrial and Commercial uses
Substrate Recommendations
- All types of concrete such as driveways, paving, footpaths, concrete roof tiles, pattern paving, stamped and slate impression paving, stencil paving, spray paving, tilt slab construction and cement sheeting
Notes
General:
- Allow a minimum 7 days for new concrete to cure prior to sealing
- For same day sealing, refer PaveCoat Cure & Seal
- Powdery or soft Concrete: DO NOT etch as this may damage the surface
- Old, Heavily Soiled/Stained Surfaces: Pre-treat the surface with Nu-EcoSafe Degreaser
- For anti-slip properties that meet AS4586 & AS4663 - P2 or P3 ratings Nutech Paint recommends AntiSlip Mix In. Ideally suited for wet areas, pools, factory loading docks, access ramps (with less than a 5° incline), stairs, entrance foyers, public pedestrian and vehicle areas.
- For further information regarding anti-slip suitability, mix ratios and standards compliance please refer to the AntiSlip Mix In TDS or PaveCoat Application Guide
Colour Accuracy Disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.
Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.
